The design uses a hollow double-walled architecture in which water flows continuously through internal channels, for structural cooling.
A YouTuber attempting to build a fully 3D printed rocket engine has tested an unusual solution to one of the biggest challenges facing plastic rocket components.
Heat. The project, created by YouTuber Mr. More Gooder, explores whether a rocket engine printed with a standard FDM printer could withstand combustion by circulating water through internal channels built directly into the engine walls. Conventional plastic rocket engines tend to fail almost immediately after ignition because the combustion chamber and nozzle rapidly reach temperatures high enough to soften or melt common printing materials. Instead of changing materials, the builder attempted to remove heat before it could destroy the structure.
The design uses a hollow double-walled architecture in which water flows continuously through internal channels, while propane and air mix separately before combustion. The concept is broadly similar to regenerative cooling techniques used in conventional liquid rocket engines, although implemented here with consumer-grade printing methods andand failed almost instantly after ignition. The combustion chamber softened rapidly, and the structure deformed within seconds as exposed plastic sections began melting. The builder then redesigned the engine using a two-wall structure.
Water circulated between the inner wall exposed to combustion gases and the outer structural shell using a small pump connected through printed adapters. Before firing, the system was pressure-tested for leaks. Ignition used two-bolt electrodes that generated an electrical arc, but later tests switched to a grill lighter after the electrodes themselves began bending from heat. The revised engine performed noticeably better.
During testing, the water-cooled combustion chamber remained intact and operated longer than previous versions. However, another issue quickly appeared. Sections lower in the nozzle that were not cooled began to overheat and sag while molten plastic dripped from the engine outlet.
“The cooled section held up well, but the other section, not so much,” the creator explained in the video. To address the failure point, the builder developed a fully water-cooled version printed as a single piece with cooling channels covering all areas exposed to combustion gases. Initial results again appeared promising, and the engine operated longer while maintaining structural stability.
The test ended when a leak formed in the inner wall, allowing coolant to enter the combustion area and extinguish the flame. Post-test analysis suggested the issue may be linked to a more fundamental material limitation. Standard FDM plastics conduct heat poorly, meaning the inner wall must reach very high temperatures before heat can radiate outward toward the coolant. Thinner walls could improve heat transfer but would reduce structural strength and pressure resistance.
The project also highlighted another challenge for any future Water reservoirs, pumps, and plumbing increase weight, potentially reducing payload capacity and overall performance. Although the experiment did not produce a fully functioning plastic rocket engine, it demonstrated that active cooling significantly improves survivability and may provide a path for further development. Kaif Shaikh is a journalist and writer passionate about turning complex information into clear, impactful stories. His writing covers technology, sustainability, geopolitics, and occasionally fiction.
A graduate in Journalism and Mass Communication, his work has appeared in the Times of India and beyond. After a near-fatal experience, Kaif began seeing both stories and silences differently. Outside work, he juggles far too many projects and passions, but always makes time to read, reflect, and hold onto the thread of wonder. Innovation
Additive Manufacturing Aerospace Combustion Cooling DIY Engineering Experiment FDM Hobby Engineering Propulsion Prototype Regenerative Cooling Rocket Rocket Engine Rocketry Space STEM Water Cooling Youtuber
United States Latest News, United States Headlines
Similar News:You can also read news stories similar to this one that we have collected from other news sources.
Unsafe water warning issued for one of America’s most visited beach destinationsPlanning a summer beach trip? Santa Monica Pier ranked as one of California's most polluted beaches for the fifth consecutive year, Heal the Bay says.
Read more »
Protesters raise concerns about water, transparency with proposed data centerHundreds of people gathered at the Utah State Capitol Saturday to protest the proposed Stratos data center project in Box Elder County.
Read more »
Denver-area water parks open for summer while conserving water amid droughtDenver‑area water parks opened for the season Saturday as Water World and Elitch Gardens rolled out new conservation measures amid worsening drought and tightening water restrictions.
Read more »
Swimmer chokes, scratches boy at water park after he splashes her with water: policeA short-tempered woman was arrested after she allegedly strangled and scratched a child for splashing water on her at a waterpark, according to police. Marjorie C. Aliprandi, 68, grabbed the young …
Read more »